金鹏康1,,
尉笑1,
王自元2,
魏哲超2,
刘惠岳2,
金鑫1
1.西安建筑科技大学环境与市政工程学院,西安 710055
2.浙江丰林染整有限公司,嘉兴 314500
基金项目: 国家科技支撑计划项目(2014BAC13B06)
Transformation of reactive red M-3BE during the treatment process of the dual-step ozone induced flotation
WANG Jia1,,JIN Pengkang1,,
WEI Xiao1,
WANG Ziyuan2,
WEI Zhechao2,
LIU Huiyue2,
JIN Xin1
1.School of Environmental and Municipal Engineering, Xi'an University of Architectural and Technology, Xi'an 710055, China
2.Zhejiang Fenglin Flax Dyeing and Finishing Co.Ltd., Jiaxing 314500, China
-->
摘要
HTML全文
图
参考文献
相关文章
施引文献
资源附件
访问统计
摘要:针对传统污泥法对印染废水中有机物去除效果有限的问题,利用多级臭氧气浮中试实验系统(DOIF)对活性红M-3BE印染废水进行深度处理,研究不同操作参数对DOIF工艺处理效果的影响,优化DOIF工艺。为进一步确定印染废水中有机物的迁移转化过程,采用紫外可见分光光度计、三维荧光(3D-EEM)和液相色谱等方法进行了分析。结果表明,臭氧气浮氧化脱色效果良好,臭氧投加量、PAC投加量和回流比分别为21 mg?L-1、9 mg?L-1和40%的情况下,废水脱色率和DOC去除率分别达到99.1%和25.2%。臭氧气浮降解活性红M-3BE的工艺中,臭氧催化氧化过程中的矿化起主要作用。其作用机理推测为,首先活性红M-3BE非对称断键为Ⅰ、Ⅱ和Ⅲ,其次Ⅰ分解为2种中间产物,并随后分解为萘和萘酚,Ⅱ分解为均三嗪,Ⅲ分解为苯环。多级臭氧气浮工艺对活性红M-3BE印染废水去除效果明显,为后续臭氧气浮技术工程化应用提供了参考依据。
关键词: 活性红M-3BE/
印染废水/
多级臭氧气浮工艺/
有机物的迁移转化特性
Abstract:Because of the limited removal efficiency for organic matters in printing and dyeing wastewater by traditional sludge process, the pilot-scale test system of the dual-step ozone induced flotation (DOIF) was developed for the advanced treatment of the printing and dyeing wastewater of reactive red M-3BE in this study. The effects of different operation parameters on DOIF treatment efficiency were studied for the optimization of this process. Then UV-vis spectrophotometer, three-dimensional fluorescence (3D-EEM) and liquid chromatography were used to identify the transformation of organic compounds in printing and dyeing wastewater. The results showed that a good decolorization performance was obtained by ozone flotation oxidization in DOIF process. At the ozone dosage of 21 mg?L-1, PAC dosage of 9 mg?L-1, and 40% reflux ratio, both the decolorization efficiency of the printing and dyeing wastewater of reactive red M-3BE and removal rate of DOC were 99.1% and 25.2%, respectively. During the degradation processing of reactive red M-3BE by DOIF, the mineralization of ozone catalytic oxidation process played a major role. The mechanism was speculated that the bonds of reactive red M-3BE were asymmetrically broken as Ⅰ, Ⅱ and Ⅲ. Then Ⅰ was decomposed into two intermediates with naphthalene and naphthol as the subsequent decomposition products. Ⅱ and Ⅲ were decomposed into mesitylene triazine and benzene ring, respectively. An obvious removal effect of printing and dyeing wastewater of reactive red M-3BE was proved for DOIF process, which provides a reference for its engineering application.
Key words:reactive red M-3BE/
printing and dyeing wastewater/
dual-step ozone induced flotation process/
transformation characteristics of organic compounds.
[1] | MCMULLAN G, MEEHAN C, CONNEELY A, et al. Microbialdecolourisation and degradation of textile dyes[J]. Applied Microbiology and Biotechnology, 2001, 56(1/2): 81-87. |
[2] | 杨继. 几种活性染料的生物降解特性研究[D]. 上海: 东华大学, 2016. |
[3] | 周红艺, 陈勇, 梁思, 等. 海藻酸钠固定化纳米铁还原脱色活性红X-3B[J]. 中国环境科学, 2016, 36(12): 3576-3582. |
[4] | 张昊, 杨清香, 李慧君, 等. 活性红M-3BE脱色真菌的筛选及脱色性能研究[J]. 环境工程学报, 2007, 1(11): 55-58. |
[5] | 杨睿媛, 王敏, 王文锋, 等. 活性红m-3BE的辐照降解研究[J]. 环境科学与技术, 2005, 28(S1): 1-3. |
[6] | 梁吉艳. 活性染料废水电化学脱色性能研究[D]. 沈阳: 东北大学, 2009. |
[7] | 董俊明, 陈晓阳. GeO2改性TiO2催化超声降解活性红(M-3BE)染料废水的应用研究[J]. 环境工程学报, 2011, 5(10): 2293-2297. |
[8] | URS V G. Ozonation of drinking water: Part I. Oxidation kinetics and product formation[J]. Water Research, 2003, 37(7): 1443-1467. |
[9] | 董淑福. 多相催化臭氧氧化法处理印染废水的研究[J].工业水处理, 2013, 33(4): 58-60. |
[10] | 李勇. 臭氧-活性炭联用处理城市生活污水研究[D]. 广州: 广东工业大学, 2005. |
[11] | 张静, 杜亚威, 刘晓静, 等. 臭氧微气泡处理酸性大红3R废水特性研究[J]. 环境科学, 2015, 36(2): 584-589. |
[12] | 杜亚威. 微气泡臭氧氧化处理酸性大红3R废水特性研究[D]. 石家庄: 河北科技大学, 2016. |
[13] | JIN P K, WANG X C, HU G. A dispersed-ozone flotation (DOF) separator for tertiary wastewater treatment[J]. Water Science & Technology, 2006, 53(9): 151-157. |
[14] | JIN P K, JIN X, VIGGO A, et al. A study on the reactivity characteristics of dissolved effluent organic matter (EfOM) from municipal wastewater treatment plant during ozonation[J]. Water Research, 2016, 88: 643-652. |
[15] | 金鹏康, 韩冬, 金鑫, 等. 多级臭氧气浮一体化装置对污水厂出水的处理效果[J]. 中国给水排水, 2015, 31(15): 12-15. |
[16] | 邱壮, 金鹏康, 王丹, 等. 多级臭氧气浮装置深度处理印染生化出水中试研究[J]. 工业水处理, 2017, 37(8): 53-56. |
[17] | 邱壮, 王锐, 金鹏康. 臭氧预氧化-混凝深度处理印染二级生化出水[J]. 印染, 2016, 42(17): 15-19. |
[18] | 杨睿媛. 活性红染料m-3BE的辐照脱色与降解研究[C]//中国化学会,上海交通大学. 第二届全国环境化学学术报告会论文集, 2004. |
[19] | 侯瑞, 金鑫, 金鹏康, 等. 臭氧-混凝耦合工艺污水深度处理特性及其机制[J]. 环境科学, 2017, 38(2): 640-646. |
[20] | 金鑫. 臭氧混凝互促增效机制及其在污水深度处理中的应用[D]. 西安: 西安建筑科技大学, 2016. |
[21] | RECKHOW D A, SINGER P C. The removal of organic halide precursors by preozonation and alum coagulation[J]. Journal of the American Water Works Association, 1984, 76(4): 151-157. |
[22] | DUAN J M, GREGORY J. Coagulation by hydrolysing metal salts[J]. Advances in Colloidand Interface Science, 2003, 100-102: 475-502. |
[23] | 汤鸿霄. 无机高分子絮凝剂的基础研究[J]. 环境化学, 1990, 9(3): 1-12. |
[24] | 栾兆坤, 汤鸿霄, 于忱非. 混凝过程中铝与聚合铝水解形态的动力学转化及其稳定性[J]. 环境科学学报, 1997, 17(3): 65-71. |
[25] | ZHAO H, LIU H, QU J. Aluminum speciation of coagulants with low concentration: Analysis by electrospray ionization mass spectrometry[J]. Colloids & Surfaces A: Physicochemical & Engineering Aspects, 2011, 379(1): 43-50. |
[26] | QI F, XU B, CHEN Z, et al. Influence of aluminum oxides surface properties on catalyzed ozonation of 2, 4, 6-trichloroanisole[J]. Separation & Purification Technology, 2009, 66(2): 405-410. |
[27] | 韩冬. 多级臭氧气浮工艺在污水深度处理中的应用研究[D]. 西安: 西安建筑科技大学, 2016. |
[28] | 侯瑞. 臭氧-混凝联合处理互促增效机制研究[C]//中国化学会应用化学学科委员会水处理化学理事会. 第十三届全国水处理化学大会暨海峡两岸水处理化学研讨会摘要集, 2016. |
[29] | 金鑫, 金鹏康, 孔茜, 等. 污水厂二级出水溶解性有机物臭氧化特性研究[J]. 中国环境科学, 2015, 35(10): 2985-2990. |
[30] | 胡刚. 臭氧-气浮工艺在深度处理中的应用[D]. 西安:西安建筑科技大学, 2005. |
[31] | ZHAO L, SUN Z, MA J. Novel relationship between hydroxyl radical initiation and surface group of ceramic honeycomb supported metals for the catalytic ozonation of nitrobenzene in aqueous solution[J]. Environmental Science & Technology, 2009,43(11): 4157-4163. |
[32] | 蒋绍阶, 刘宗源. UV254作为水处理中有机物控制指标的意义[J]. 重庆建筑大学学报, 2002, 24(2): 61-65. |
[33] | 刘建红, 王利颖, 王保贵, 等. 臭氧氧化对二级出水有机物(EfOM)特性机制的影响[J]. 环境工程学报, 2016, 10(3): 1228-1234. |
[34] | GONG J,LIU Y, SUN X.O3 and UV/O3 oxidation of organic constituents of biotreated municipal wastewater[J]. Water Research, 2008, 42(4): 1238-1244. |
[35] | WU F, TANOUE E, LIU C Q. Fluorescence and amino acid characteristics of molecular size fractions of DOM in the waters of Lake Biwa[J]. Biogeochemistry, 2003, 65(2): 245-257. |
[36] | 侯瑞, 金鑫, 金鹏康, 等. 污水厂二级出水中难凝聚有机物的臭氧化特性[J]. 环境科学, 2018, 39(2): 844-851. |
[37] | 杨岸明, 常江, 甘一萍, 等. 臭氧氧化二级出水有机物可生化性研究[J]. 环境科学, 2010, 31(2): 363-367. |
[38] | 宋晓娜, 于涛, 张远, 等. 利用三维荧光技术分析太湖水体溶解性有机质的分布特征及来源[J]. 环境科学学报, 2010, 30(11): 2321-2331. |
[39] | 孔赟, 朱亮, 吕梅乐, 等. 三维荧光光谱技术在水环境修复和废水处理中的应用[J]. 生态环境学报, 2012, 21(9): 1647-1654. |
[40] | 鞠东. 活性艳红M-3BE的化学降解与微胶囊化研究[D]. 太原: 山西大学, 2010. |
[41] | 刘海龙, 郭雪峰, 王敏慧, 等. 臭氧-混凝交互作用对混凝效果的影响[J]. 环境科学, 2015, 36(9): 3285-3291. |
[42] | 韩利华, 许红英, 陈鹏. 活性红3BE及其水解产物的液相色谱分离[J]. 河北化工, 2004(2): 31-32. |
[43] | SHANTKRITI S, SENTHIL K S. Exploring docking and aerobic-microaerophilic biodegradation of textile azo dye by bacterial systems[J]. Journal of Water Process Engineering, 2018, 22: 180-191. |
Turn off MathJax -->
点击查看大图
计量
文章访问数:1482
HTML全文浏览数:1392
PDF下载数:133
施引文献:0
出版历程
刊出日期:2019-01-08
-->
活性红M-3BE在多级臭氧气浮工艺中的迁移转化特性
王佳1,,金鹏康1,,
尉笑1,
王自元2,
魏哲超2,
刘惠岳2,
金鑫1
1.西安建筑科技大学环境与市政工程学院,西安 710055
2.浙江丰林染整有限公司,嘉兴 314500
基金项目: 国家科技支撑计划项目(2014BAC13B06)
关键词: 活性红M-3BE/
印染废水/
多级臭氧气浮工艺/
有机物的迁移转化特性
摘要:针对传统污泥法对印染废水中有机物去除效果有限的问题,利用多级臭氧气浮中试实验系统(DOIF)对活性红M-3BE印染废水进行深度处理,研究不同操作参数对DOIF工艺处理效果的影响,优化DOIF工艺。为进一步确定印染废水中有机物的迁移转化过程,采用紫外可见分光光度计、三维荧光(3D-EEM)和液相色谱等方法进行了分析。结果表明,臭氧气浮氧化脱色效果良好,臭氧投加量、PAC投加量和回流比分别为21 mg?L-1、9 mg?L-1和40%的情况下,废水脱色率和DOC去除率分别达到99.1%和25.2%。臭氧气浮降解活性红M-3BE的工艺中,臭氧催化氧化过程中的矿化起主要作用。其作用机理推测为,首先活性红M-3BE非对称断键为Ⅰ、Ⅱ和Ⅲ,其次Ⅰ分解为2种中间产物,并随后分解为萘和萘酚,Ⅱ分解为均三嗪,Ⅲ分解为苯环。多级臭氧气浮工艺对活性红M-3BE印染废水去除效果明显,为后续臭氧气浮技术工程化应用提供了参考依据。
English Abstract
Transformation of reactive red M-3BE during the treatment process of the dual-step ozone induced flotation
WANG Jia1,,JIN Pengkang1,,
WEI Xiao1,
WANG Ziyuan2,
WEI Zhechao2,
LIU Huiyue2,
JIN Xin1
1.School of Environmental and Municipal Engineering, Xi'an University of Architectural and Technology, Xi'an 710055, China
2.Zhejiang Fenglin Flax Dyeing and Finishing Co.Ltd., Jiaxing 314500, China
Keywords: reactive red M-3BE/
printing and dyeing wastewater/
dual-step ozone induced flotation process/
transformation characteristics of organic compounds
Abstract:Because of the limited removal efficiency for organic matters in printing and dyeing wastewater by traditional sludge process, the pilot-scale test system of the dual-step ozone induced flotation (DOIF) was developed for the advanced treatment of the printing and dyeing wastewater of reactive red M-3BE in this study. The effects of different operation parameters on DOIF treatment efficiency were studied for the optimization of this process. Then UV-vis spectrophotometer, three-dimensional fluorescence (3D-EEM) and liquid chromatography were used to identify the transformation of organic compounds in printing and dyeing wastewater. The results showed that a good decolorization performance was obtained by ozone flotation oxidization in DOIF process. At the ozone dosage of 21 mg?L-1, PAC dosage of 9 mg?L-1, and 40% reflux ratio, both the decolorization efficiency of the printing and dyeing wastewater of reactive red M-3BE and removal rate of DOC were 99.1% and 25.2%, respectively. During the degradation processing of reactive red M-3BE by DOIF, the mineralization of ozone catalytic oxidation process played a major role. The mechanism was speculated that the bonds of reactive red M-3BE were asymmetrically broken as Ⅰ, Ⅱ and Ⅲ. Then Ⅰ was decomposed into two intermediates with naphthalene and naphthol as the subsequent decomposition products. Ⅱ and Ⅲ were decomposed into mesitylene triazine and benzene ring, respectively. An obvious removal effect of printing and dyeing wastewater of reactive red M-3BE was proved for DOIF process, which provides a reference for its engineering application.