镍掺杂铝酸镧涂层的制备及其红外辐射性能

删除或更新信息，请邮件至freekaoyan#163.com(#换成@)

本站小编 Free考研考试/2022-01-01

刘鹏飞¹，卢卫华¹，韩召^1,2,3*，陈义祥³，李江涛³

1. 安徽工业大学冶金工程学院，安徽马鞍山 2430022. 安徽工业大学冶金减排与资源综合利用教育部重点实验室，安徽马鞍山 2430023. 中国科学院理化技术研究所，北京 100190

收稿日期:2017-12-28修回日期:2018-03-20出版日期:2018-12-22发布日期:2018-12-19
通讯作者:韩召

基金资助:国家自然科学基金资助项目;钢铁冶金新技术国家重点实验室开放研究项目

Preparation and infrared radiation characterization of Ni doped lanthanum aluminate coatings

Pengfei LIU¹, Weihua LU¹, Zhao HAN^1,2,3*, Yixiang CHEN³, Jiangtao LI³

1. School of Metallurgy Engineering, Anhui University of Technology, Ma?anshan, Anhui 243002, China2. Key Laboratory of Metallurgical Emission Reduction & Resources Recycling, Ministry of Education, Anhui University of Technology, Ma?anshan, Anhui 243002, China3. Technical Institute of Physics and Chemistry, Chinese Academy of Sciences, Beijing 100190, China

Received:2017-12-28Revised:2018-03-20Online:2018-12-22Published:2018-12-19

Supported by:The National Natural Science Foundation of China

摘要/Abstract

摘要： 采用溶胶?凝胶法合成了Ni2+掺杂的LaAlO3基红外辐射材料LaAl0.6Ni0.4O2.89 (LANO)，以其为辐射基料，利用喷涂工艺在氧化铝陶瓷片表面制备红外辐射涂层，考察了磷酸二氢铝、铝溶胶、硅溶胶和钠水玻璃4种粘结剂对涂层物相组成、热稳定性和红外辐射性能的影响. 结果表明，以LANO为辐射基料、铝溶胶为粘结剂时，涂层红外辐射性能最佳，3?5 ?m波段红外发射率达0.93；所制涂层具有良好的抗热震性能，50次热震后涂层未明显剥落失效；涂层具有显著的强化辐射传热效果，节能率达31.7%.

引用本文

刘鹏飞卢卫华韩召陈义祥李江涛. 镍掺杂铝酸镧涂层的制备及其红外辐射性能[J]. 过程工程学报, 2018, 18(6): 1261-1266.
Pengfei LIU Weihua LU Zhao HAN Yixiang CHEN Jiangtao LI. Preparation and infrared radiation characterization of Ni doped lanthanum aluminate coatings[J]. Chin. J. Process Eng., 2018, 18(6): 1261-1266.

使用本文

0
/ / 推荐
导出引用管理器 EndNote|Ris|BibTeX
链接本文:http://www.jproeng.com/CN/10.12034/j.issn.1009-606X.217439
http://www.jproeng.com/CN/Y2018/V18/I6/1261

参考文献

[1]Robert S, Stephebn D.High-Emissivity Coating Technology Improves Annealing Furnace Efficiency[J].Iron Amp Steel Technology, 2007, 4(5):319-324 [2]Kleeb T, Olver J.High-Emissivity Coatings for Energy Savings in Industrial Furnaces[J].Industrial Heating, 2007, 74(6):57-61 [3]白皓, 王苗, 苍大强, 等.高炉热风炉用高发射率涂料的节能效果及机理分析[J].北京科技大学学报, 2010, 32(07):915-921 [4]Bai H, Wang M, Cang D Q et al.Energy-Saving Effect and Mechanism Analysis of High Emissivity Coatings for BF Hot Blast Stoves[J].Journal of University of Science and Technology Beijing, 2010, 32(07):915-921 [5]冯胜山, 鲁晓勇, 许顺红.高温红外辐射节能涂料的研究现状与发展趋势[J].工业加热, 2007, 36(1):10-15 [6]Feng S S, Lu X Y, X S H.Research status and Development of Infrared Radiation Energy Saving Coatings Used in High Temperature[J].Industrial Heating, 2007, 36(1):10-15 [7]Lu L, Fan X A, Zhang J, et al.Evolution of Structure and Infrared Radiation Properties for Ferrite-Based Amorphous Coating [J].Applied Surface Science, 2014, 316(15): 82-87 [8]Shen X, Li L, Wu X, et al.Infrared Emissivity of Sr doped Lanthanum Manganites in Coating Form[J].Journal of Alloys & Compounds, 2011, 509(31):8116-8119 [9]王晓, 侯佩民, 徐元浩, 等.红外辐射涂料的现状及其发展方向[J].上海涂料, 2012, 50(7):31-34 [10]Wang X, Hou P M, Xu Y H, et al.The Current Situation and Development Direction of Infrared Radiant Coatings[J].Shasnghai Coating, 2012, 50(7):31-34 [11]樊希安, 张坚义, 陆磊, 等.堇青石--铁氧体基复合节能涂层的结构与红外辐射性能[J].硅酸盐学报, 2014, 42(7):891-896 [12]Fan X A, Zhang J Y, Lu L, et al.Microstructure and Infrared Radiation Properties of Cordierite-Ferrite Based Energy-Saving Composite Coating[J].Journal of Chinese Ceramic Society, 2014, 42(7):891-896 [13]He X D, Li Y B, Wang L D, et al.High Emissivity Coatings for High Temperature Application: Progress and Prospect[J].Thin Solid Films, 2009, 517(17):5120-5129 [14]Tucker R, Ward J.Identifying and Quantifying Energy Savings on Fired Plant Using Low Cost Modelling Techniques[J].Applied Energy, 2012, 89(1):127-132 [15]卢卫华, 刘鹏飞, 韩召, 等.镍离子掺杂对铝酸镧红外辐射性能的影响[J].硅酸盐学报, 2017, 45(03):371-377 [16]Lu W H, Liu P F, Han Z, et al.Effect of Ni3+ Doping on Infrared Radiation Properties of Lanthanum Aluminate [J].Journal of the Chinese Ceramic Society, 2017, 45(03):371-377 [17]Povoden-karadeniz E, Grundy A N, Chen M, et al.Thermodynamic Assessment of the La-Fe-O System[J].Journal of Phase Equilibria and Diffusion, 2009, 30(4):351-366 [18]W?rnhus I, Vullu P E, Holmestad R, et al.Electronic Properties of Polycrystalline LaFeO3Part I: Experimental Results and the Qualitative Role of Schottky Defects[J].Solid State Ionics, 2005, 176(37-38):2783-2790 [19]翁端, 丁红梅, 徐鲁华, 等.锶和铈对+λ稀土纳米钙钛矿材料性能的影响[J].中国稀土学报, 2001, 19(4):338-342 [20]Weng D, Ding H M, Xu L H, et al.Effect of f Strontium and Cerium on Performances of Nanometer LaMnO3+λ Rare-Earth Perovskite[J].Journal of the Chinese Rare Earth Society, 2001, 19(4):338-342 [21]Han Z, Li X W, Ye J K, et al.Significantly Enhanced Infrared Emissivity of LaAlO3 by Co-Doping with Ca2+ and Cr3+for Energy-Saving Applications[J].Journal of the American Ceramic Society, 2015, 98(8):2336-2339 [22]Han Z, Liu J, Li X W, et al.Ca2+-Doped LaCrO3: A Novel Energy-Saving Material with High Infrared Emissivity[J].Journal of the American Ceramic Society, 2014, 97(9):2705-2708 [23]Choi M, Janotti A, Walle C G V D, et al.Native Point Defects in LaAlO3: A Hybrid Functional Study[J].Physical .Review B, 2013, 88(21):214117-214117 [24]Ouellette D G, Moetakef P, CAIN T A, et al.High-density Two-Dimensional Small Polaron Gas in a Delta-Doped Mott Insulator[J].Scientific Reports, 2013, 3(7476):3284-3284 [25]Stefanidis G D, Van Gem K M, Heynderickx G J, et al.Evaluation of High-Emissivity Coatings in Steam Cracking Furnaces Using a Non-grey Gas Radiation Model[J].Chemical Engineering Journal, 2008, 137(2):411-421 [26]孙家跃, 杜海燕, 石春山.标度二元氧化物酸碱性质的新方法[J].化学通报, 1991, 2(2):19-22 [27]Sun J Y, Du H Y, Shi C S.A New Method for Scaling Acid - base Properties of Binary Oxides[J].Chemistry, 1991, 2(2):19-22 [28]董元篪，王海川.冶金物理化学[M]. 合肥工业大学出版社, 2012：100-106. [29]Dong Y C, Wang H C.Metallurgical Physical Chemistry [M]. Hefei University of Technology Press, 2012:100-106. [30]Dhahri A, HorchaniI-naifer K, Benedetti A, et al.Combustion Synthesis and Photoluminescence of Eu3+ Doped LaAlO3 Nanophosphors[J].Optical Materials, 2012, 34(11):1742-1746

相关文章 15

[1]	代国强汤晶刘雯谭淑君刘斌王文庆刘天中苏革. 环氧树脂涂层表面亲水性对微藻黏附性能的影响[J]. 过程工程学报, 2020, 20(7): 832-842.
[2]	黄文薛召露刘侠倪振航吴朝军张世宏. 喷涂功率对YSZ涂层的力学性能和抗铝硅熔体腐蚀性能的影响[J]. 过程工程学报, 2020, 20(12): 1463-1471.
[3]	沈文豪张亚新宋江. 基于CFD-DEM方法的净化器流场模拟与结构优化[J]. 过程工程学报, 2020, 20(10): 1147-1155.
[4]	毛绍宝杨英李海庆张世宏. MoSi₂和(Mo,W)Si₂涂层的宽温域氧化过程[J]. 过程工程学报, 2019, 19(4): 826-835.
[5]	王赶强王景甫张新欣张涛. 金属基有机硅树脂涂层复合材料的导热性能[J]. 过程工程学报, 2018, 18(4): 785-791.
[6]	刘慧敏诸林郁辰阳曹文浩陈建良. 耦合酸气提浓的脱硫脱碳工艺[J]. 过程工程学报, 2018, 18(4): 879-885.
[7]	韩召刘鹏飞李小伟卢卫华. 利用Ca2+掺杂增强钙钛矿型LaFeO3的红外发射率[J]. 过程工程学报, 2018, 18(1): 154-158.
[8]	杨波. 全液压压裂车功率节能匹配优化[J]. 过程工程学报, 2017, 17(4): 853-858.
[9]	南剑饶政华刘骁浚贺慧敏廖胜明. 基于系统节能的冶金过程监测与模拟技术研究进展[J]. , 2014, 14(4): 708-714.
[10]	李克江张建良张亚鹏刘征建姜曦. 基于节能减排思想分析炼铁工艺的发展[J]. , 2014, 14(1): 162-172.
[11]	杨松峰李云伟朱永平. 热电池隔热涂层的制备与性能[J]. , 2013, 13(3): 519-524.
[12]	杨金杯余美琼郑志功邱挺. 醋酸甲酯和甲醇热集成变压精馏分离工艺模拟与优化[J]. , 2013, 13(1): 105-110.
[13]	徐文青李寅蛟朱廷钰曹万杰. 中国钢铁工业CO2排放现状与减排展望[J]. , 2013, 13(1): 175-180.
[14]	田林周扬民谢刚侯彦青方宁杨妮. 以酚醛树脂为粘结剂的铝电解槽冷捣糊的研制[J]. , 2011, 11(3): 519-523.
[15]	姚星合朱永平张伟刚. 热处理工艺对纳米氧化锆粉体微观结构与涂层性能的影响[J]. , 2011, 11(1): 124-130.

PDF全文下载地址:

http://www.jproeng.com/CN/article/downloadArticleFile.do?attachType=PDF&id=3181