基于机电建模的加工中心轴间耦合问题

删除或更新信息，请邮件至freekaoyan#163.com(#换成@)

清华大学辅仁网/2017-07-07

基于机电建模的加工中心轴间耦合问题

赵彤, 谢溢, 胡建

清华大学机械工程系, 精密超精密制造装备与控制北京市重点实验室, 北京 100084

Multi-axis coupling of machining centers based on electromechanical modeling

ZHAO Tong, XIE Yi, HU Jian

Beijing Key Laboratory of Precision/Ultra-Precision Manufacturing Equipments and Control, Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China

摘要:

输出: BibTeX | EndNote (RIS)

摘要加工中心加工精度与其整机结构特性和各轴控制特性密切相关。考虑进给轴间的动态激励响应，研究加工中心整机在特定频率范围内的各向动柔度，对辅助机床设计具有重要意义。该文结合有限元建模和相关实验方法，分析了某双驱进给平台的结构动柔度，重点研究其机械系统的轴间耦合问题。提出了一种用传递函数组等效机械结构特性的整机机电联合仿真建模方法，并以此研究了某卧式加工中心机电系统的轴间耦合问题。研究结果表明：当加工中心存在某些模态振型同时影响刀具或工件在多方向的变形时，其机械系统和机电系统的轴间耦合在整机动柔度研究和控制环参数选择时必须予以考虑。

关键词 ：加工中心,轴间耦合,有限元建模,机电建模

Abstract：The dynamic accuracy of a machining center is strongly influenced by its structural dynamics and control loops. The frequency response of the entire machine including the multi-directional dynamics is important in the machine tool design phase. The structural dynamics of a twin ball screw feed machine are analyzed using a finite element analysis (FEA) and measurements with a focus on the multi-axis coupling of its mechanical system. Then, an electromechanical modeling method is developed where the structural dynamics are replaced by transfer functions to study the multi-axis coupling of the electromechanical system of a horizontal machining center. The results show that when there are modal shapes leading to displacements of the tool or the workpiece in multiple directions, the multi-axis coupling of the machining center must be considered in studies of the dynamics and control parameters.

Key words：machining center multi-axis coupling finite element modeling electromechanical modeling

收稿日期: 2016-05-26 出版日期: 2017-02-21

ZTFLH:

TG502.3

引用本文:

赵彤, 谢溢, 胡建. 基于机电建模的加工中心轴间耦合问题[J]. 清华大学学报（自然科学版）, 2017, 57(2): 113-119.
ZHAO Tong, XIE Yi, HU Jian. Multi-axis coupling of machining centers based on electromechanical modeling. Journal of Tsinghua University(Science and Technology), 2017, 57(2): 113-119.

链接本文:

http://jst.tsinghuajournals.com/CN/10.16511/j.cnki.qhdxxb.2017.22.001或 http://jst.tsinghuajournals.com/CN/Y2017/V57/I2/113

图表:

图1 TCB1双驱进给平台

表1 进给平台部分结合部参数

图2 进给平台模态实验

表2 进给平台模态分析结果

图3 进给平台x向激励仿真与实验结果对比

图4 进给平台各向结构动柔度

图5 双驱卧式加工中心机电系统结构

表3 卧加整机部分结合部参数

图6 卧加整机部分模态振型

图7 卧加整机各向结构动柔度

图8 卧加整机z向控制环模型

表4 卧加整机控制环主要参数

图9 卧加整机机电联合仿真模型

图10 控制参数对整机动柔度G_zz的影响

参考文献:

[1]	Altintas Y, Brecher C, Weck M, et al. Virtual machine tool[J]. CIRP Annals:Manufacturing Technology, 2005, 54(2):115-138.
[2]	叶佩青, 王仁彻, 赵彤, 等. 机床整机动态特性研究进展[J]. 清华大学学报:自然科学版, 2012, 52(12):1758-1763.YE Peiqing, WANG Renche, ZHAO Tong, et al. Recent research advances of whole machine tool dynamics[J]. Journal of Tsinghua University:Science and Technology, 2012, 52(12):1758-1763. (in Chinese)
[3]	Wang L, Liu H T, Yang L, et al. The effect of axis coupling on machine tool dynamics determined by tool deviation[J]. International Journal of Machine Tools and Manufacture, 2015, 88:71-81.
[4]	董冠华, 殷勤, 殷国富, 等. 机床结合部动力学建模与辨识方法的研究[J]. 机械工程学报, 2016, 52(5):162-168.DONG Guanhua, YIN Qin, YIN Guofu, et al. Research on dynamics modeling and identification of machine tool joints[J]. Chinese Journal of Mechanical Engineering, 2012, 52(5):162-168. (in Chinese)
[5]	Dhupia J S, Powalka B, Ulsoy A G, et al. Effect of a nonlinear joint on the dynamic performance of a machine tool[J]. Journal of Manufacturing Science and Engineering, 2007, 129(5):943-950.
[6]	Frey S, Dadalau A, Verl A. Expedient modeling of ball screw feed drives[J]. Production Engineering, 2012, 6(2):205-211.
[7]	Namazi M, Altintas Y, Abe T, et al. Modeling and identification of tool holder-spindle interface dynamics[J]. International Journal of Machine Tools and Manufacture, 2007, 47(9):1333-1341.
[8]	郭垒. MCH63加工中心结构件及结合部的建模和分析方法研究[D]. 北京:清华大学, 2011.GUO Lei. Modeling and Analysis Study of the Structural Components and Joints of Machining Center MCH63[D]. Beijing:Tsinghua University, 2011. (in Chinese)
[9]	张辉, 于长亮, 王仁彻, 等. 机床支撑地脚结合部参数辨识方法[J]. 清华大学学报:自然科学版, 2014, 54(6):815-821.ZHANG Hui, YU Changliang, WANG Renche, et al. Parameters identification method of machine tool support joint[J]. Journal of Tsinghua University:Science and Technology, 2014, 54(6):815-821. (in Chinese)
[10]	Altintas Y, Verl A, Brecher C, et al. Machine tool feed drives[J]. CIRP Annals:Manufacturing Technology, 2011, 60(2):779-796.
[11]	叶献彬, 张东升, 冯斌. 基于ADAMS与MATLAB的数控机床伺服进给驱动系统联合仿真[J]. 机床与液压, 2013, 41(15):160-163.YE Xianbin, ZHANG Dongsheng, FENG Bin. United simulation about CNC machine tool feed drive system based on ADAMS and MATLAB[J]. Machine Tool and Hydraulics, 2013, 41(15):160-163. (in Chinese)
[12]	胡芳, 叶文华. 基于刚柔-机电耦合的龙门机床主轴进给驱动联合仿真[J]. 机械设计与制造工程, 2016, 45(1):27-31.HU Fang, YE Wenhua. Co-simulation of the spindle servo feed system of gantry machine tool based on rigid-flexible and electrical-mechanical coupling[J]. Machine Design and Manufacturing Engineering, 2016, 45(1):27-31. (in Chinese)
[13]	Neugebauer R, Scheffler C, Wabner M. Implementation of control elements in FEM calculations of machine tools[J]. CIRP Journal of Manufacturing Science and Technology, 2011, 4(1):71-79.
[14]	Weck M, Queins M, Witt S. Coupled simulation of control loop and structural dynamics[J]. Annals of the German Academic Society for Production Engineering, 2003, X(2):105-110.
[15]	Brecher C, Altstaedter H, Daniels M. Axis position dependent dynamics of multi-axis milling machines[J]. Procedia CIRP, 2015, 31:508-514.

No related articles found!