二维码（扫一下试试看！） | | 铝药型罩环形聚能射流的数值模拟 | | Numerical Simulation of Annular Shaped Charge with Al Liner | | 投稿时间：2019-03-06 | | DOI：10.15918/j.tbit1001-0645.2019.071 | | 中文关键词:环形聚能射流起爆方式长径比数值模拟 | | English Keywords:annular shaped chargemodes of initiationlength-to-diameter rationumerical simulation | | 基金项目:国家自然科学基金资助项目（U1830139） | | | 摘要点击次数:741 | | 全文下载次数:667 | | 中文摘要: | | 基于一种药型罩材料为铝的环形聚能装药结构，通过Autodyn软件模拟不同起爆方式（起爆环直径D1）和不同长径比（L/D）的装药，计算得到环形射流的成型过程和速度分布曲线.分析数值模拟结果发现：环形射流成型过程主要受长径比影响，长径比较小时射流发生内偏，长径比较大时射流发生外偏；射流轴向速度主要受长径比影响，长径比越大轴向速度越大，头部轴向速度最大相差约700 m/s；射流径向速度主要受起爆方式影响，平均径向速度最大相差为220 m/s，起爆环直径和长径比在较小或较大时，射流径向速度梯度较大；结合射流成型和速度结果，D1=0.5D、L/D=1.0时射流综合性能较好.侵彻混凝土板试验的通孔直径为装药直径的2.6倍，数值模拟结果与试验结果误差为7.7%，验证了计算模型及算法的合理性. | | English Summary: | | Based on an annular shaped charge with aluminum liner, different modes of initiation (initiation radius D1) and length-to-diameter ratio (L/D) were simulated by Autodyn to measure the formation and jet speed of the annular jet. Numerical results showed that the formation process of the annular jet was mainly influenced by L/D, the jet tip had an inward deflection when L/D was relatively small, and an outward deflection otherwise. The axial jet speed was positively related to and also mainly influenced by L/D, and the maximum difference was about 700 m/s. The radial jet speed was mainly influenced by modes of initiation, and the maximum radial jet speed difference was about 220 m/s. The radial jet speed gradient was greater when D1 or L/D was relatively small or big. Combined with jet formation and speed, D1=0.5D and L/D=1.0 were preferred settings for this charge. The hole diameter of the concrete target was 2.6D1, which is 7.7% bigger than the numerical result. The penetration experiment demonstrates that the calculation model and method are appropriate. | | 查看全文查看/发表评论下载PDF阅读器 | |
李维浩,姚世明,李蔚清,苏智勇.面向AR沙盘异地协同标绘的动作重构技术[J].北京理工大学学报（自然科学版）,2019,39(12):1298~1303,1320.LIWei-hao,YAOShi-ming,LIWei-qing,SUZhi-yong.AMotionReconstructionTec ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21.北京理工大学学报2019年总目次（第39卷）[J].北京理工大学学报（自然科学版）,2019,39(12):1321~1338..[J].TransactionsofBeijingInstituteofTechnology,2019,39(12):1321-1338.二维码（扫一下试试看！）北京理 ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21张志广,李宁,包云肽,张阳天.基于小波变换的离子迁移谱信号处理技术[J].北京理工大学学报（自然科学版）,2019,39(S1):164~167.ZHANGZhi-Guang,LINing,BAOYun-Tai,ZHANGYang-Tian.SignalProcessingTechnologyfor ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21汪怡平,郭承奇,王涛,黎帅,姚云龙.基于自由变形技术的Ahmed模型气动减阻优化[J].北京理工大学学报（自然科学版）,2018,38(3):221~228.WANGYi-ping,GUOCheng-qi,WANGTao,LIShuai,YAOYun-long.AerodynamicDragRedu ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21孙崔源,薛里,孟海利,付天杰,康永全.几种典型爆破振动控制技术的试验研究[J].北京理工大学学报（自然科学版）,2018,38(4):359~363,370.SUNCui-yuan,XUELi,MENGHai-li,FUTian-jie,KANGYong-quan.ExperimentalResea ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21王登峰,蔡珂芳,张帅,马明辉.基于激光拼焊技术的汽车B柱结构优化设计[J].北京理工大学学报（自然科学版）,2018,38(7):691~697,708.WANGDeng-feng,CAIKe-fang,ZHANGShuai,MAMing-hui.StructureDesignofAutomotiv ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21范世鹏,祁琪,路坤锋,吴广,李伶.基于改进人工势场法的巡航导弹自主避障技术[J].北京理工大学学报（自然科学版）,2018,38(8):828~834.FANShi-peng,QIQi,LUKun-feng,WUGuang,LILing.AutonomousCollisionAvoidanceTec ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21邵楠,步志超,李柏,陈玉宝.清远连州CINRAD/SA-D型业务试验双偏振天气雷达技术评估[J].北京理工大学学报（自然科学版）,2018,38(9):953~958.SHAONan,BUZhi-chao,LIBai,CHENYu-bao.TheTechnologyEvaluationofS-Ban ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21邱忠超,张卫民,高玄怡,张瑞蕾.基于PSO-LSSVM的疲劳裂纹漏磁定量识别技术[J].北京理工大学学报（自然科学版）,2018,38(11):1101~1104,1140.QIUZhong-chao,ZHANGWei-min,GAOXuan-yi,ZHANGRui-lei.Quantitative ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21.北京理工大学学报2018年总目次（第38卷）[J].北京理工大学学报（自然科学版）,2018,38(12):1321~1338..[J].TransactionsofBeijingInstituteofTechnology,2018,38(12):1321-1338.二维码（扫一下试试看！）北京理 ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21
| |
