二维码（扫一下试试看！） | | 基于等效热-力载荷的20Cr2Ni4预应力车削残余应力模拟及实验 | | Simulation and Experimental Research on Residual Stress in Pre-Stress Turning of 20Cr2Ni4 Based on Equivalent Loading Theory | | 投稿时间：2017-05-16 | | DOI：10.15918/j.tbit1001-0645.2018.07.001 | | 中文关键词:等效热-力载荷预应力切削残余应力 | | English Keywords:equivalent thermal-mechanical loadingpre-stress cuttingresidual stress | | 基金项目:国家部委基础产品创新科研项目（VIDP5102） | | | 摘要点击次数:809 | | 全文下载次数:449 | | 中文摘要: | | 为快速准确预测20Cr2Ni4合金钢预应力车削表面残余应力的分布，基于等效热-力载荷建立三维有限元仿真模型，通过切削热-力模型确定等效热-力载荷的分布形状和强度，将切削过程等效为接触正应力、接触剪应力和热流通量在已加工表面的循环作用.模拟的残余应力分布趋势与测量结果基本吻合.基于上述模型研究了切削速度、进给量和预应力大小对残余应力分布的影响.结果表明，切削速度对残余应力分布影响不明显，减小进给量能使表面残余拉应力和最大残余压应力减弱，增加预应力能够有效地减小表面残余拉应力和增大最大残余压应力. | | English Summary: | | In order to predict the distribution of residual stress of 20Cr2Ni4 steel in pre-stress turning, a 3D finite model was established based on equivalent loading theory to transfer the cutting process into a combined cycle effect of contact normal stress, tangential stress and heat flux. The shape and value of equivalent thermal-mechanical loadings were extracted from analytical model of cutting force and heat. The simulation results of residual stress distribution are basically consistent with the measured results. Analyzing and comparing the simulation results, the influences of cutting speed, feed rate and pre-stress on residual stresses distribution were studied. These results show that the effect of cutting speed on residual stresses distribution is not obvious. With the decrease of feed rate, surface residual tensile stress and the maximum compressive stress decrease accordingly. Moreover, the increase of pre-stress leads to the decrease of surface residual tensile stress and the increase of the maximum compressive stress. | | 查看全文查看/发表评论下载PDF阅读器 | |
王震坡,薛雪,王亚超.基于自适应无迹卡尔曼滤波的分布式驱动电动汽车车辆状态参数估计[J].北京理工大学学报（自然科学版）,2018,38(7):698~702.WANGZhen-po,XUEXue,WANGYa-chao.StateParameterEstimationofDistributedDr ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21.北京理工大学学报2018年总目次（第38卷）[J].北京理工大学学报（自然科学版）,2018,38(12):1321~1338..[J].TransactionsofBeijingInstituteofTechnology,2018,38(12):1321-1338.二维码（扫一下试试看！）北京理 ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21刘静,侯宇,苏婷慧,张庆,邵毅敏.基于模块化设计的特种车辆减振降噪技术研究[J].北京理工大学学报（自然科学版）,2018,38(S1):38~43.LIUJing,HOUYu,SUTing-hui,ZHANGQing,SHAOYi-min.StudyonVibrationControlandNoi ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21黄文彬,丁晓喜,杜明刚,邵毅敏.机械传动系统的智能感知技术[J].北京理工大学学报（自然科学版）,2018,38(S1):33~37.HUANGWen-bin,DINGXiao-xi,DUMing-gang,SHAOYi-min.IntelligentSensingTechnologyforMech ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21刘勇.轮毂电机驱动多轴越野车辆总体技术探讨[J].北京理工大学学报（自然科学版）,2018,38(S1):55~58.LIUYong.TheStudyonGeneralTechnologyofIn-WheelMotorDriveMultiaxisOff-RoadVehicle[J].Transact ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21郭志强,门日秀,闫柯,孙钰杰.特种车辆涡轮增压器内部流动特性分析[J].北京理工大学学报（自然科学版）,2018,38(S1):59~62.GUOZhi-qiang,MENRi-xiu,YANKe,SUNYu-jie.AnalysisonInternalFlowCharacteristicsofSp ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21谢霞,张学玲,段秀兵,徐柳.轮履变体式车辆底盘越障性能研究[J].北京理工大学学报（自然科学版）,2018,38(S1):107~111.XIEXia,ZHANGXue-ling,DUANXiu-bing,XULiu.ResearchonObstacle-SurmountingPerformance ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21江燕华,马忠民,徐达,李中好,骆振兴.某越野车辆平顺性仿真分析及综合评价[J].北京理工大学学报（自然科学版）,2018,38(S1):103~106.JIANGYan-hua,MAZhong-min,XUDa,LIZhong-hao,LUOZhen-Xing.RideComfortSimulati ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21刘辉,张聪,韩立金,曹福辉,王伟达,侯旭朝.带耦合机构的串联式履带车辆直驶稳定性控制[J].北京理工大学学报（自然科学版）,2018,38(S1):112~116.LIUHui,ZHANGCong,HANLi-jin,CAOFu-hui,WANGWei-da,HOUXu-chao.StraightD ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21张志达,李韶华,刘星,周军魏.全轮转向多轴车辆性能分析及侧翻前馈预警研究[J].北京理工大学学报（自然科学版）,2018,38(S1):142~146.ZhangZhida,LiShaohua,LiuXing,ZhouJunwei.PerformanceAnalysisandRolloverFeed ... 北京理工大学科研学术 本站小编 Free考研考试 2021-12-21
| |
