姓　　名：
王庆航

职　　称：
讲师

最高学位：
博士

行政职务：
无

导师类别：
硕导

所在系部：
材料成型与控制工程

电子邮件：
wangqinghang@yzu.edu.cn

专业方向：
材料学/材料加工工程

研究方向
高强度、高塑性、高室温成形性能镁合金材料的制备及其动/静态再结晶行为研究

研究成果
近五年内，在《Journal of Materials Scienceand Technology》《Materials Science &Engineering: A》、《Journal of alloys and compounds》、《Journal of Materials Research & Technology》等期刊发表SCI论文13篇，其中代表性论文如下：
[1]WangQinghang, Jiang Bin,et al.Pre-strain effect on twinning and de-twinning behaviors of Mg-3Li alloy traced by quasi-in-situ EBSD[J]. Materials Science & Engineering A2020, 798: 140069.
[2]WangQinghang, Jiang Bin,et al. Reduction per pass effect on texture traits and yield anisotropy of Mg-Al-Zn-Mn-Ca alloy subjected to unidirectional and cross rolling[J]. Journal Material Research Technology 2020, 9: 9607-9619.
[3]WangQinghang, Jiang Bin,et al.Unveiling annealing texture formation and static recrystallization kinetics of hot-rolled Mg-Al-Zn-Mn-Ca alloy[J]. Journal of Materials Science & Technology 2020, 43: 104–118.
[4]WangQinghang, Jiang Bin,et al.Fabrication of Mg/Mg composite with sleeve-core structure and its effect on room-temperature yield asymmetry via bimetal casting-co-extrusion[J]. Materials Science & Engineering A 2020, 769: 138476.
[5]WangQinghang, Jiang Bin,et al.Twin nucleation, twin growth and their effects on annealing strengths of Mg-Al-Zn-Mn sheets experienced different pre-compressive strains[J]. Journal of Alloys and Compounds 2020, 815: 152310.
[6]WangQinghang, Jiang Bin,et al.Formation of the elliptical texture and its effect on the mechanical properties and stretch formability of dilute Mg-Sn-Y sheet by Zn addition[J]. Materials Science & Engineering A 2019, 746:259–275.
[7]WangQinghang, Song Jiangfeng, Jiang Bin,et al.An investigation on microstructure, texture and formability of AZ31 sheet processed by asymmetric porthole die extrusion[J]. Materials Science & Engineering A 2018, 720:85–97.
[8]WangQinghang, Jiang Bin, Tang Aitao, et al.Enhanced stretch formability at room temperature for Mg-Al-Zn/Mg-Y laminated composite via porthole die extrusion[J]. Materials Science & Engineering A 2018, 731: 184–194.
[9]WangQinghang, Jiang Bin, Tang Aitao,et al.A micro-alloyed Mg-Sn-Y alloy with high ductility at room temperature[J]. Materials Science & Engineering A 2018, 735:131–144
[10]WangQinghang, Jiang Bin, Tang Aitao,et al.A good balance between ductility and stretch formability of dilute Mg-Sn-Y sheet at room temperature[J]. Materials Science & Engineering A 2018, 736: 404–416.
[11]WangQinghang, Jiang Bin, Tang Aitao,et al.Ameliorating the mechanical properties of magnesium alloy: Role of texture[J]. Materials Science & Engineering A 2017, 689:395–403.
[12]WangQinghang, Jiang Bin,et al.Tailoring the textures and mechanical properties of AZ31 alloy sheets using asymmetric composite extrusion[J]. Materials Science&EngineeringA2016, 673: 606–615.

科研项目
扬州市高层次人才科研启动基金（主持，在研）

教授课程
《金属材料与热处理》本科生课程

工作经历
2020.10-至今 扬州大学机械工程学院 材料加工系 讲师

学习经历
2014.09-2020.10重庆大学 材料科学与工程 博士（硕博连读）
2010.09-2014.06内蒙古科技大学 金属材料工程 学士

招生意愿
每年招收硕士研究生1-2名，大学生创新工程本科生2名