教育及工作经历：
1. 2018/06–至今， 北京理工大学， 机械与车辆学院，预聘助理教授(副研究员)
2. 2017/08–2018/06， 约翰霍普金斯大学(美国)， 机械工程，博士后，合作导师：GretarTryggvason
3. 2016/01–2017/08， 圣母大学(美国)， 航空与机械工程，博士后，合作导师：GretarTryggvason
4. 2010/09–2015/07， 清华大学， 机械工程， 工学博士，导师：汪劲松、向东
5. 2006/09–2010/07， 北京工业大学， 机械工程及自动化，工学学士
研究方向：
多物理场建模分析、装配过程多场建模仿真;
多相流数值计算、3D打印工艺建模仿真
代表性论文：
[1] H Xia, J Lu, G Tryggvason*. Simulations of fused filament fabrication using a front tracking method[J]. International Journal of Heat and Mass Transfer, 2019, 138: 1310-1319.
[2] D Xiang, H Xia*, W Yang, P Mou. Parametric study and residual gas analysis of large-area silicon-nitride thin-film deposition by plasma-enhanced chemical vapor deposition[J]. Vacuum, 2019, 165: 172-178.
[3] H Xia, J Lu, G Tryggvason*. A numerical study of the effect of viscoelastic stresses in fused filament fabrication. Computer Methods in Applied Mechanics and Engineering, 2019, 346(4), 242-259.
[4] H Xia, J Lu, G Tryggvason*. Fully resolved numerical simulations of fused deposition modeling. Part II–solidification, residual stresses and modeling of the nozzle. Rapid Prototyping Journal, 2018, 24(6): 973-987.
[5] H Xia, J Lu, S Dabiri, G Tryggvason*. Fully resolved numerical simulations of fused deposition modeling. Part I: fluid flow. Rapid Prototyping Journal, 2018, 24(2): 463-476.
[6] H Xia, D Xiang*, P Mou, W Yang. Experimental study of the effects of showerhead configuration on large-area silicon-nitride thin film by plasma-enhanced chemical vapor deposition. Thin Solid Films, 2017, 638: 1-8.
[7] H Xia, D Xiang*, W Yang, P Mou. Multi-model simulation of 300 mm silicon-nitride thin-film deposition by PECVD and experimental verification. Surface and Coatings Technology, 2016, 297: 1-10.
[8] H Xia*, D Xiang, W Yang, P Mou. The segmented non-uniform dielectric module design for uniformity control of plasma profile in a capacitively coupled plasma chamber. AIP Advances, 2014, 4(12): 127124.
[9] H Xia*, D Xiang, P Mou. The array-control heater and non-uniform resistance module design for regulating the temperature profile in a reactor chamber. Journal of Mechanical Science and Technology, 2015, 29(2): 593-604.
[10] H Xia*, D Xiang, P Mou. Simulation-Based Optimization of a Vector Showerhead System for the Control of Flow Field Profile in a Vertical Reactor Chamber. Advances in Mechanical Engineering, 2014, 6: 525102.
[11] D Xiang, H Xia^*, W Yang, et al. New simulation-based approach for the profile control in a process chamber: Fluid, thermal, and plasma profile. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 2015, 231(3): 565-580.
学术会议/报告:
[1] H Xia, J Lu, S Dabiri, and G Tryggvason. Fully resolved numerical simulations of fused deposition modeling: 14th United State National Congress Computational Mechanics (USNCCM). Montreal, Canada. July 17 – July 20, 2017.
[2] H Xia, J Lu, G Tryggvason. Modeling and Simulations of Fused Deposition Modeling (FDM): Graduate Seminar in Fluid Mechanics, Johns Hopkins University, Feb. 09,2018.
[3] G Tryggvason, H Xia, J Lu. Numerical Simulations of Fused Filament Fabrication:American Physical Society (APS) Meeting, 2018.
[4] G Tryggvason, H Xia, J Lu. Fully Resolved Simulations of 3D Printing: American Physical Society (APS) Meeting. 2017.
成果及荣誉:
第六届『上银优秀机械博士论文』佳作奖，2016
社会职务:
Surface & Coatings Technology(SCI), Rapid Prototyping Journal(SCI), AIP Advances(SCI)等期刊审稿人